Keg Dispensing Supplies

Long and narrow, the dip tube brush was made specifically for cleaning out keg dip tubes. Being long and narrow themselves, dip tubes can be tricky to clean properly without the right tool. Cleaning out a dip tube with a dip tube brush ensures that you scrub the whole inner surface of the dip tube, where bacteria and beer stone can easily hide. These brushes are also good for cleaning sight glasses and other narrow brewing equipment. Another brush highly recommended to anyone who owns a keg!

Oetiker clamps provide a permanent clamping solution! This style of clamp has a 1-ear design, which means they are crimped at a single point on the clamp to create a superior seal over your tubing. These large Oetiker clamps are often used on 5/16" thick-walled tubing that is used in CO2 connections on kegging and draft systems. These clamps hold tight, creating a great seal that holds for a long time! Some people prefer these for more permanent systems. If you are looking to switch over to a snug seal that lasts, make sure you use Oetiker clamps!

Taprite has long been a trusted name in the beverage industry. Known for their high quality craftsmanship, Taprite has one of the best regulators on the market! These dual guage regulators have a low pressure gauge which shows output pressure (supports 0 - 50 PSI), and a high pressure gauge that shows the remaining pressure in the cylinder. Taprite regulators are known for having high quality diaphragms which stand up to the test of time much better than cheaper or lower-quality regulators, as well as being more accurate for a longer period of time. The regulator also includes a standard CO2 barb with shutoff valve and a safety check.

This is the ball needed for the Guiness "U" coupler which prevents backflow. As opposed to the check valve ball on a standard keg, the ball found in the Guiness coupler is slightly larger. Make sure you have the right one for your coupler!

Superflush Tap & Line Cleaner is an safe, easy-to-use, economical and biodegradable line cleaner perfect for use on kegerators and draft dispensing systems. Simply mix 2-3 oz. with 1 gallon water as per the instructions and pump through lines. Allow to sit in lines for a few minutes, then flush clean with water. A solution made at the same rate may be used to clean faucet and coupler parts as well. Sold in a 32 oz bottle, Superflush can help you keep your lines pristine, pouring perfect beer every time!

Three is better than one! This 3" beer tower extension not only extends your tower, but comes with two shanks for adding two more faucets to your tower setup. With the existing fauet, this means that you can have up to three beer faucets on your setup! Perfect for going big with your existing 3" beer tower, get your extension today!

Chrome replacement collar for the Perlick Perl faucet.

Turn your fridge into a kegerator with our kegerator homebrew kegging system! This system comes with all the internal workings of a kegerator system you will need, except the CO2 cylinder.

Included is a high quality Taprite regulator, ball lock gas line assembly, a brand new 5 gallon cornelius keg, a ball lock liquid disconnect with swivel nut set, 6 feet of 3/16" ID Bevlex thick-walled liquid tubing, and a full shank assembly that includes a standard beer faucet, faucet knob, 4" shank, 1/4" tailpiece, beer nut and neoprene washer. Make the draft system you have always wanted with this kegerator kegging system, complete with a brand spankin' new keg!

All you'll need in addition to this kit to make the ultimate kegerator, is a full CO2 tank. For local customers we sell full tanks at all of our retail locations!

Party Pig Valve Assem with gasket

3" Chrome Dual Tap Tower

A 4-way manifold is the perfect way to carbonate four kegs at once, or to pressurize kegs and run a Blichmann BeerGun at the same time! The CO2 can be hooked up from the regulator via the barb on the side of the manifold using standard 5/16" ID Bevlex tubing, and the other barbs can be run with the same tubing to gas disconnects for carbonating and dispensing from kegs, or to other CO2 driven devices. When mounted, the barbs run straight downward. Includes shutoff valves on the four top barbs on the manifold, which give another level of protection from lost CO2!

This is a replacement black lever washer for standard faucets. It goes on top of the white faucet shaft washer on the faucet lever of a standard faucet. Washers wear out over time, and used equipment that has not been properly maintained may need new washers. If this is the case, Great Fermentations has replacements for you!

Party Pig with tray, strap, and 2 pressure pouches

Want to make your own kegerator? Have a tower that you need replaced? Great Fermentations offers these 3" beer towers for all your tower needs! This model is a standard 3" model, which works well as a replacement on kegerators that have the same sized tower. It has a single beer faucet attached to the tower. If you are making your own kegerator, you can affix this to the top of a dorm fridge or other small refridgerator. Just like that, you've got yourself a kegerator! The sleek chrome finish looks nice as your pour the perfect beer from the tower. Cheers!

Chrome Bonnet for Perlick Forward Faucet

This replacement o-ring fits on Perlick faucets. It is the o-ring that seals the lever component of the faucet. Integral in the proper functioning of these Perlick faucets, it is never a bad idea to have an extra on hand!

Perlick Friction Ring

These check valves are the perfect solution to backflow issues that you may be having. They go on the gas side of a ball or pin lock gas system. They have an integrated back check valve that helps prevent flow from reversing, and fit on the 1/4" MFL fitting found on most standard ball or pin lock disconnects. Keep your gas lines clean with these as a preventative measure.

Get that coupler into your kegerator! Some kegerators don't have a lot of clearance space, and a standard keg coupler won't fit on top of the keg. The solution to this problem? A low-profile sanke coupler! This coupler measures a mere 3.25", taking up less space above your keg than normal couplers. It has a unique design by which the engaging mechanism twists down the body and engages into the keg. Above the engaging body, the CO2 comes in the sideways barb, and liquid flows out sideways as well. Perfect for kegerator setup without a lot of vertical room! This coupler comes with an integrated gas barb. Not included is a 3/16" liquid tailpiece, beer nut and neoprene washer.

Need new o-rings for the inside of your stout faucet? Look no further! Great Fermentations have these o-rings available to you so that you can keep those creamy beers flowing! These o-rings fit in the body of the faucet above the nozzle and keep everything tight and secure. Have a few on hand so you'll always be prepared for the inevitable!

Most keg couplers work the same, with many similar parts. The Guiness "U" coupler is no exception. It too has a check valve ball and a retainer for the ball. The Guiness ball and retainer are, however, different, and thus require different replacement parts that the reguilar. If you are in need of a new check valve retainer for your Guiness coupler, look no further than Great Fermentations!