Keg Dispensing Supplies

The faucet knob is the handle part of your faucet assembly. These black faucet knobs are 2.75 inches long and screw into the lever post just above the bonnet, giving you a way to get a handle on your beer! Make sure you have one of these for each of your faucets so you can pour pints for your friends and family.

For tapping American and Canadian kegs economically! This economy US sanke coupler is manufactured by Krome and will fit standard American and Canadian kegs requiring a "D" style connection. This coupler, popularly known as a tap, comes with the gas side connections. Not included is a 3/16" barbed liquid tailpiece, beer nut and neoprene washer for liquid side connections. If you are looking to dispense beer on a budget, look no further than this economy US sanke coupler!

Finally, a standard faucet made of above-standard material! These standard faucets are anything but standard, with full stainless steel bodies and levers. Stainless steel is the holy grail of beer materials! Sleek and stylist, it not only looks great, but is durable and will last longer than chrome or brass faucets. The simple design means that the faucets are easy to take apart and clean. For beer faucets that will last longer, stainless steel faucets can't be beat!

Do you have a home draft system and use both a sanke coupler and ball or pin lock kegs? Instead of going through the routine of disconnecting your sanke coupler and reattaching ball or pin lock connections every time, make your life easier with a few of these tailpieces! They have a 1/4" MFL connnection and can be used in conjunction with a hex beer nut and a neoprene washer on both the gas and liquid side of your sanke coupler. Simply replace your existing tailpieces with these, and hook up the respective swivel nuts to your gas and liquid lines.Whenever you want to use sanke or ball/pin lock connections, you can easily attach the swivel nuts to either setup!

Please Note that we recommend using a flare fitting washer on the sanke side to completely seal the metal-on-metal connections (most modern ball and pin lock disconnects have plastic on the end of their connection, so a flare fitting washer is uneccessary unless you have an older style disconnect.) Make life easier for yourself and serve beer through any type of connection!

A great, easy way to make CO2 and keg connections!The pin lock gas dispensing kit is a 3-foot length of 5/16" ID Bevlex tubing with a ball lock gas disconnect and 5/16" swivel nut set worm-clamped on one end, and a small worm clamp on the other that can be used to connect the assembly to a CO2 manifold or regulator. Always good to have around, especially for carbonating several kegs at once!

Gas lost in your CO2 system can lead to a shorter life span of your CO2 cylinders. Prevent CO2 loss with a washer! A plastic CO2 washer fits between your CO2 cylinder and regulator and helps to create a good seal. A good seal ensures that you don't lose gas when carbonating or serving. These plastic CO2 washers fit Taprite brand regulators, as well as many standard-sized CO2 regulators. Keep a few on hand in case of an emergency!

A swivel nut set with a barb for your liquid side connections! These swivel nut sets come with a standard 1/4" female flared nut and a 1/4" barb. This swivel nut set is perfect for use with standard 3/16" ID liquid tubing, thin or thick-walled. These can be connected directly to the standard liquid disconnects that we offer, or used with a plastic flare fitting for any direct metal-on-metal connections.

Keep that check valve ball from escaping with a check valve ball retainers! This little winged piece of plastic fits in the shaft of your standard sanke coupler, holding the check valve ball in place so that backflow does not become an issue. Protect the investment of your beer and dispensing equipment by having one of these on hand should the unthinkable loss of the original retainer occur!

Use this portable CO2 charger as a way to dispense beer from a Corny keg without dragging along your CO2 tank. No tanks. No hoses. It takes about two 16 gram non-threaded CO2 cartridges (Item # GF111, not included) to dispense a carbonated keg. Trigger valve allows precise control of gas. Charger connects directly to a gas ball or pin lock disconnect to dispense beer.

German beer lovers rejoice! This "A" style German slider keg coupler, also known as a tap, is just what you need to get beer flowing from German kegs! This coupler is like no other, with a cupped mount that slides onto the keg and locks in place when engaged. This is the most widely used keg coupler in Germany, and while it will not work with all German beer kegs, it does work with most of them, as well as with a few Belgian kegs. Among the breweries that use the "A" coupler are Ayinger, Achouffe, Bitburger, Franziskaner, Hacker-Pschorr, Hoegaarden, Paulaner, Spaten, and Warsteiner. This coupler comes with the gas side connections, but does not include the liquid side connections which consist of a 3/16" liquid tailpiece, a beer nut and a neoprene washer.

Do you often carbonate and serve beer at the same time? If so, or if you would like to be able to do both at different pressures, a secondary regulator is perfect for you! Your primary CO2 regulator attaches to your CO2 tank and allows one output pressure. However, a secondary regulator hooks up inline and allows you to regulate to another keg at a lower pressure. This allows you to carbonate one keg at a higher pressure while serving beer from another at a lower pressure! This Taprite secondary regulator is made to the same high standards as all Taprite equipment, with a high quality diaphragm that keeps regulating long after lesser regulators give up the ghost. Regulate at multiple pressures with a secondary regulator from Taprite!

Ever noticed how your homebrew attracts those pesky fruit flies (or drosophila melanogaster in the science world)? Seems they show up a lot easier and quicker than they leave, and are a real pain to kill. Introducing the Fruit Fly Bar Pro, Fly Strip. This ingenious product has a controlled release technology to slowly diffuse a deep penetrating vapor in enclosed spaces for up to 4 months. Vapor is clean and odorless, and evenly distributed throughout the enclosed treatment area. Kills visible and invisible (yes, even ones with invisibility cloaks on) insects on contact, and prevents new insect infestations. Works in enclosed spaces of up to 200 cubic feet. A must have for an active homebrew draft system area. Want proof? Then check out this video below

The Keg Line Cleaning Kit is the key to keeping your faucets, lines, and couplers clean. This kit includes a hand pump and cleaning solution container that attaches to your faucet shank, a 32 oz. bottle of Superflush Keg and Line Cleaner, a double ended faucet brush and a spanner wrench for removing faucets and attaching the cleaning pump.

Simply mix the Superflush Keg and Line Cleaner at the recommended rate of 2 to 3 oz. per gallon of water and use this solution to soak faucet and coupler parts. Remove the faucet from the shank using the spanner wrench, and attach the cleaning solution container to the shank with the spanner wrench. Pump solution through the liquid line and out into a bucket, then allow solution to sit in the lines for a few minutes. Fill the cleaning solution container with water and pump through to flush lines. Use the double ended brush to clean faucet and coupler, then flush with water and reassemble. Repeat when changing kegs to keep beer flowing free of foaming issues, beer stone buildup and bacterial infection.