- Let us help you get started on you endeavor to build an electric brewery. As we build these as well, we have all the parts you need to build your brewery in one location. Give us a few days to assemble and package all the parts you need to build your own BCS brewery. Save yourself time and effort, while also reducing the tools needed to build your brewery. Usual lead time is 3-5 days, as each package is made to order Pictured 50a 2 element kit Let us help you get started. Build a complete 50a 4-element (1bbl) BCS control panel using our complete package. Here we provide the parts you need to build an electric brewing panel from the box out. The resulting panel should be a near complete version of the panels we build and sell. All the hardware and wire you may need to get your panel built. Some build pictures can be found on our Flickr Page View the wiring schematic HERE The kit includes: Basic Kit Hardware 12 - LEDs (4 white 220v, 2 white 110v, 2 yellow 110v, 2 blue 110v, 1 red 110v, and 1 green 220v) 1 - Emergency Stop locking push button with NC Contact 5 - 3-Way Switches with NO Contacts for element select and pumps (on-off-auto) 5 - Additional NO Contacts for back of 3 way switches 1 - Key toggle Switch for panel on/off 5 - 63a DIN Contactors w/ 110v Coils for main power for element control 4 - 40a Solid State Relays for BCS control of elements 1 - 12v Power supply unit for SPDT Relay board 1 - Triple relay, SPDT Relay board for pumps and arlam 1 – Large pre-drilled and tapped heat sink for element SSRs 1 meter of DIN rail cut in 1/3m increments 30 - Terminal Blocks for wire from 6-24 awg 4 - New style 32a 2 pole DIN Rail Breaker 1 - New style 6a 1 pole DIN Rail Breaker 20 - Terminal block anchoring ends 8 - Terminal block end covers 6 - Terminal block separators 4 - Terminal block connecting bridge pieces Enclosure and outlets 1 – Enclosure 24w x 20t x 8d 4 – L6-30 Flanged outlets for elements 2 – L5-15 Flanged outlets for pumps 1 – C6375 flanged inlet for main power supply 2 – L5-15 plugs for pumps 1 – C6364C Connector for main power supply 4 – XLR Male connectors for temperature input 1 – Panel Network connector Tags for panel include: Power / Off-On Alarm / Off-On Stop Element Select / HLT-Off-Boil HLT Element / Auto-Off-On Boil Element / Auto-Off-On Water Pump / Auto-Off-On Wort Pump / Auto-Off-On 2 - HLT 2 - Boil Water Pump Wort Pump HLT Probe MASH Probe Boil Probe KO Probe 240v / 50a 120v / 6a BCS Controller and temperature probes BCS 460 Temperature Control Unit DIN Rail Outlet 4 - 4 inch or 6 inch Temperature Probes 4 - 1/4" inch to 1/2" inch MNPT Compression fittings 4 - 1/2" inch Locknuts 4 - 1/2" inch washer and o-rings 4 – XLR Female connectors for temperature probes 30 ft of 1/8 inch braided poly sleeve for temperature probes 4 cuts of 3 1/8 inch heat shrink tubing for temperature probes M12 probes will ship with M12 connector on the probe end, and a bare end for XLR on the other end Wiring and wire fittings 6 ft Range style main power cable 25 ft of black 10 gauge wire 25 ft of red 10 gauge wire 25 ft of green 10 gauge wire 60 ft of black 14 gauge wire 20 ft of white 14 gauge wire 10 ft of red 18 gauge wire 10 ft of blue 18 gauge wire 10 ft of purple 18 gauge wire 4 ft of gray 18 gauge wire 4 ft of tan 18 gauge wire 36 ft of yellow 18 gauge wire 36 ft of orange 18 gauge wire 20 ft of white 18 gauge wire 10 - #10 Yellow Spade connectors for 10ga wire connections on SSR relays 100 - #6 Blue Spade Connectors for most 110v wiring throughout the panel 50 - #6 Red spade connectors for the low voltage and temp probe wiring 5 - #10 Blue ring connectors for grounding wire on enclosure posts *** BCS Temperature Controller Options*** BCS460 with upto 4 temperature inputs BCS462 with upto 8 temperature inputs *** Enclosure Information *** Painted Enclosure is included. The included enclosures has no cuts made to the box requiring and therefore allowing you to design and build your system to your preference. Pre-cut Painted Enclosures uses our current Assembled enclosure layout, is CNC cut out of the painted box and then we drill and tap all necessary holes for easy hardware mounting. The paint on the enclosure is likely to have some marks and may even be loose at some edges; we highly recommend you plan on sanding and painting with your choice of paint. Stainless enclosure. Same as the standard painted option, but instead we send a 304 Stainless enclosure. Pre-cut Stainless enclosure is the equivalent of an enclosure straight from our cut stack for the assembled panels, these are cut, cleaned, drilled and tapped. All kits include a printed copy of our wiring guide book. Tools you will need include: Wire Cutters Wire strippers Crimping tools for spade and ring connectors Phillips screw driver(s) Flat head screw driver(s) Zip ties and zip tie bases (optional) Labeler or other means to tag wires If you are cutting your control panel 7/8" Hole saw or step bit for LEDs and switches 3/4" hole saw for XLR panel connectors 1-1/2" hole saw for flanged pump outlets 2-1/8" hole saw for flanged element outlets Dremel or other rotary tool for cutting network panel inlet Sand paper and paint recommended for painted enclosures. Scotch Bright scrubbers work well for smoothing and cleaning the stainless.
Weight: 60 lbs.
Free Shipping: N/A